9600 Series
The 9600 Series features seal conversions that can be done easily in the field. This pump’s Stainless Steel construction ensures a long life. It can be easily assembled and disassembled, with an adjustable relief valve. The 9600 Series has pressures up to 100 PSI, and flows up to 165 GPM.
- SST Construction
- Easy Assembly / Disassembly
- Optional Hydraulic Motor Drive Arrangement
- Optional Gearbox
Standard Construction Materials
- Housings 316 stainless steel (ASTM A743)
- Gears & Shafts 17-4PH (ASTM 564 Type 630)
- Carbon graphite journal bearings
- Teflon™ case gaskets
- Teflon™ mechanical seal or graphite impregnated Teflon™ packing
Configuration Options
- Direct couple hydraulic motor drive bracket (SAE A or SAE B)
- Easy field conversion between mechanical seal & packing
- GHB option
Typical Applications
- Transferring wide range of corrosive products, acids, caustics, & solvents
9600 Series
Stainless steel service that is dedicated to performing above and beyond your expectations.
9600 Series Nomenclature
The FIGURE number consists of a thirteen digit number.
The first digit (9) indicates the stainless steel series.
- 9 = stainless steel
The second digit (7) indicates shaft sealing.
- 6 = Packing
- 7 = Mechanical Seal
The third and fourth digits (22) indicates the approximate theoretical displacement in U.S. gallons per 100 revolutions.
.22 Gallons/100 Rev. [Liters/100 Rev.]
The letter or group of letters (GHB) indicates the pump head arrangement.
- HB = Pump with outboard bearing
- GHB = Pump with outboard bearing and built-on gear reduction unit
- BH = Pump without outboard bearing to accommodate close coupled hydraulic drive auxiliaries through a rigid coupling
The letter (F) indicates port style.
- F = Pump with Roper standard flange ports
On GHB pumps, the letter (O) indicates pump with outboard bearing and auxiliary mounting provisions. (Does not include built-on gear reduction unit.)
The letters (RV) indicates pump equipped with a relief valve.
- No letters = Without relief valve
- RV = RV Style relief valve
The letter or group of letters (X, LX) indicates direction of rotation and shaft position. The letter (L) indicates low drive unit. If the letter (L) is not used, the shaft will be in a high drive position.
- No letter or W = Clockwise Rotation (Standard Rotation)
- Z = Counterclockwise Rotation
- LX = Counterclockwise Rotation
- LY = Clockwise Rotation
Occasionally, special pumps or configurations are required which are unique for a particular application. These modifications are clarified by a SPECification number. Identification of any items different than a standard pump can be made by consulting Roper Pump Company or an authorized distributor.
The TYPE number is a number used by Roper Pump Company for in-house identification of construction. Always include the type number in any references to the pump.
- A = low pressure spring (standard)
- B = high pressure spring
The SERIAL number is a unique number assigned to each pump built by Roper Pump Company.
In any communication concerning this pump, always be sure to include the Figure, Spec, Serial, and Type numbers so proper identification of the pump can be assured.
Rebuild Kits
Major rebuild kits available for standard pumps. See distributor or manufacturer for more details.
9600 Series - Size & Specification Chart
Note: Maximum speed and flow can only be achievable under the correct inlet (suction) and liquid conditions. Liquid viscosity and discharge pressure, plus pumping conditions will determine actual flow (ie. – theoretical minus slip).
9600 Pump Series Documents
Questions?
9722HBFRV-1A
9722MBHFRV-13661-1A
9622HBFRV-1A
9622GHBFRV-1460A
9722MHBFRV-17855-1B
9722GHBFRV-1460A
9622MBHFRV-13661-1A
9722MHBFRV-17834-1B
9722HBFRV-1B
9722GHBFRV-1460B
9722GHBFRV-1394A
9722BHFRV-1A
