Roper Pump Company Webstore

Our dedicated merchandise store, designed exclusively for our channel partners and employees. We’ve curated a wide selection of apparel and promotional gifts, all branded with our company logo.

3632 Pump

3632 Series Pump

Need more flow out of your 3″ pump? Load and unload your tanks faster. Roper Pump’s 3632 pump increases the flow rate for your 3” pump, giving you: faster tank turnover, more money in your pocket, and less time on the road.

Take a short, 5-question quiz to see if the 3632 pump will increase your flow rate.

SIZE AVAILABLE
0
NPT PORT
0 "
GPM (UP TO)
0
PSI (UP TO)
0

3632 Liquid transport pump Packing Options

Triple Lip Seal

Offering the same high degree of sealing reliability as a mechanical seal, triple lip seals are better suited for viscous products that tend to set up while the pump is idle.

Mechanical seal faces tend to stick together with high viscosity liquids, such as resins, glues and paints. The lips create an effective barrier to product leakage, and will move freely upon resumption of pumping a thickening substance.

In cases where extreme circumstances can cause catastrophic failure of mechanical seals, the resilient nature of the triple lip seal makes it relatively immune to sudden failure.

Optional: Triple Lip Seal with
Packing Backup

With the addition of the packing backup, users can tighten the packing down if the TLS fails to control a leak until maintenance can be performd.

DSA Packing

DSA (Dry run, Self-Adjusting) is shaft packing that is designed to be virtually leak free.

In tests at Roper on a unit pumping #2 fuel oil at 450 RPM and 45 PSI, the shaft packing only leaked one drop in 500 hours of operation.

DSA packing is good for clean liquids that do not crystallize or thicken/harden when exposed to air or temperature extremes. These packing sets come with installation instructions that must be followed for the packing to work properly.

The rings are made of graphite. Part of the rings are die formed wedge shaped graphite filament while others are typical braided rings. The die formed rings are fragile and will not take rough handling.

DSA packing requires minimal compression and rare adjustment. Compressing this packing like conventional packing will result in excessive leakage that cannot be stopped without replacing the entire packing set. It will provide very good service when properly installed and maintained.

3632 Pump

Compare the flow rate of the 3632 with other pumps...

3632 Pump Nomenclature

The first digit (3) indicates the port arrangement.

  • 3 = 3600 Series with right angle ports
  • 4 = 4600 Series with straight through ports

The second digit (6) indicates a packing seal.

  • 2 = Triple Lip Seal with Back-Up Packing
  • 5 = Triple Lip Seal or “standard” Cartridge Seal (use “C” in special model options)
  • 6 = Packing
  • 7 = Mechanical Seal or any non-standard Cartridge Seal (use with “C” in special model options) that is further explained by use of a spec number

The third and fourth digits (11) indicate the approximate theoretical displacement in U.S. gallons per 100 revolutions. Gallons/100 Rev. [Liters/100 Rev.]

  • 11 [41.6]
  • 17 [64.4]
  • 22 [83.3]
  • 32 [121.1]
  • 35 [132.5]
  • 43 [162.8]
  • 48 [181.7]
  • 58 [219.6]
  • 65 [246.0]

The letter or group of letters indicates special model options (precedes letters to indicate pump arrangement).

  • E = EVO options included
  • C = Cartridge seal provisions
  • EC = EVO plus cartridge seal provisions, including ANSI machined for backplate

The letter or group of letters (GHB) indicates the pump head arrangement. Backplate machined for cartridge seal use.

  • HB = Pump with outboard bearing
  • SBH = Short backplate with outboard bearing and triple lip seal
  • GHB = Pump with outboard bearing and built-on gear reduction unit
  • BH = Pump without outboard bearing to accommodate close coupled hydraulic drive auxiliaries through a rigid coupling.
  • H: Backplate

On GHB pumps, the letter (O) indicates pump with outboard bearing and auxiliary mounting provisions (does not include built-on gear reduction unit).

The letter (F or A) indicates port style

  • No letter = Pump with threaded ports
  • F = Pump with Roper standard flange ports
  • A = Pump with flange facing to accept ANSI Flanges

The letters (RV) indicate type of faceplate on pump.

  • RV = RV style single direction relief valve faceplace (Standard RV, Jacketed RV)
  • BV = Bi-directional relief valve faceplate (Not available on sizes 35 &58)
  • No Letters = Plain Faceplate

The letter or group of letters (X, LX) indicates direction of rotation and shaft position. The letter (L) indicates low drive unit. If the letter (L) is not used, the shaft will be in a high drive position.

  • No letter or W = Clockwise Rotation (Standard Rotation)
  • X = Counterclockwise Rotation
  • Y = Clockwise Rotation
  • Z = Counterclockwise Rotation
  • LW = Clockwise Rotation
  • LX = Counterclockwise Rotation
  • LY = Clockwise Rotation
  • LZ = Counterclockwise Rotation

Occasionally, special pumps or configurations are required which are unique for a particular application. These modifications are clarified by a SPECification number. Identification of any items different than a standard pump can be made by consulting Roper Pump Company or an authorized distributor.

The TYPE number is a number used by Roper Pump Company for in-house identification of construction. Always include the type number in any references to the pump.

  • A = low pressure spring (standard)
  • B = high pressure spring

The SERIAL number is a unique number assigned to each pump built by Roper Pump Company.

In any communication concerning this pump, always be sure to include the Figure, Spec, Serial, and Type numbers so proper identification of the pump can be assured.

Rebuild Kits

Major rebuild kits available for standard pumps. See distributor or manufacturer for more details.

3632 Pump - Size & Specification Chart

Note: Maximum speed and flow can only be achievable under the correct inlet (suction) and liquid conditions. Liquid viscosity and discharge pressure, plus pumping conditions will determine actual flow (ie. – theoretical minus slip).

3632 Pump Series Documents

Questions?

3611GHB-10101-3460
3622HBFRV-3A
3611HB-3
3611GHB-3460
3711HB-3
3622MBHFRV-13661-3A
3611HBRV-3A
3617HBFRV-3A
3617HBRV-3A
3611HFZ-G10845-3
3648HBFRV-3A
3617HB-3
3622HBF-3
3722HBFRV-3A
3611HBZ-3
3611MBHFX-17632-3
3611HBFRV-3A
3617HB-16326-3
3517MBHFRV-17099-3A
3522HBFRV-3A
3611HB-16326-3
3611GHBO-3
3622HBFRV-5023-3A
3611MBHFZ-17334-3
3622GHBFRV-3460A
3617MBHFRV-13661-3A
3611GHB-17097-3460
3548HBFRV-3A
3611HLY-G10040-3
3658HBFRV-3A
3622GHBFRV-3320A
3222MBHFRV-17296-3A
3648MBHFRV-13842-3A
3622HBF-16326-3
3611MBHFBVZ-17703-3A
3717MBHFRV-14433-3A
3622GHBFRV-3394A
3222HBFRVZ-10771-3A
4622HBFRV-3A

3222MBHFRV-17296-3B
3648MBHF-14646-3
4658HBFRV-3A
3611GHBO-2423-3
3517MBHFRV-17774-3A
3622HBFRV-5788-3A
3548MBHF-14856-3
3748MBHF-13842-3
3611GHBFRV-3460A
4617HBF-3
3622GHBFORV-3A
3617HZ-G9845-3
3617HB-17647-3
3548MBHFRV-14856-3A
4622MBHFRV-13661-3A
3658GHBFRV-3426A
3548MBHFRV-13842-3A
3622HBFZ-3
3611MBHRV-13661-3A
3265HBFY-17966-3
3611HBF-3
3748HBFRV-3A
3711HBFRV-3A
3622MBHFX-17144-3
3222MBHFRV-13661-3B
3617HBF-3
3611HBLW-3
3632HBFRV-3A
3622MBHFRV-13660-3A
3522HBFRVY-9580-3B
3611HBRV-16326-3A
3611GHBRV-3460A
3611GHBRV-3320A
3222HBFRV-3B
3748MBHFRV-17212-3A
3222HBFRVZ-10771-3B
3265HBFRV-17886-3B
3611GHBORV-3A
3635HBFRV-3A
3711GHBRV-3320A
3622HBFRV-3B
4658GHBFRV-3426A
3648MBHF-13842-3
3648HBF-3
TXD2.5, Blackmer

Scroll to Top

New changes are coming soon...

We’re launching a brand new website on August 1st. We’ll be going dark on July 31st in preparation for this big change, so mark your calendars and be ready to see some modern, updated designs on our website!

  • 00Days
  • 00Hrs
  • 00Mins
  • 00Secs
Roper Pump Transparent White Logo
This website uses cookies. By proceeding navigating on this page, you agree to the use of the cookies according to the terms of our Privacy Policy.
Roper Pump Transparent White Logo
This website uses cookies. By proceeding navigating on this page, you agree to the use of the cookies according to the terms of our Privacy Policy.